Last week of lecture!!! Learning More!!!

This week lecture is about electric and digital electronic.


  On the electric class, our lecturer ask us to complete 3 tasks, there is extension wire, ac fluorescent light, dc fluorescent light setup. Before we start to do it, lecturer give out the explanation and direction of the electric setup. The extension wire setup need us to connect the wire to 3 pin plug and also the socket. 3 pin plug made by 4 component, there are fuse, earth terminal(green yellow colour), neutral terminal(blue colour), and live terminal(brown colour). Both the connection in 3 pin plug and socket are the same, just connect the 3 wires to their terminal respectively, but the connection of wire must follow the direction, otherwise will cause the black out of current. 


The composition of 3 pin plug as shown as below.



  In the connection of ac fluorescent light and dc fluorescent light, the component inside the body of fluorescent light almost the same: wire, starter and ballast. To light up the dc or ac fluorescent light, the ballast inside the body play a important role as they using the different ballast. The crossing wire inside the ac fluorescent light is more complicated than in dc fluorescent as it use up 3 wire: earth, neutral, and live. Dc fluorescent light only has to connect positive and negative terminal of dc supply, so it is suitable to use in car.


******************************************************************************************************


  In the lecture of digital electronic, we mainly understand about the analog input, digital output , and also the binary system. The digital electronic playing part in almost everyone daily life and it is the heart of electronic. It make the system function by converting analog data to digital data. The binary system as the counting system in digital electronic interpret the digital system by logic number 1 or 0. Binary number are ideal to use in digital electronic system as it has only 2 valid value.


  Binary number using base 2 number instead of using base 10 number. There is using power square number, 1, 2, 4, 8, 16, 32, and so on. The binary system also represents the bit of the system, the binary digit (bit) showing the discrete voltage level of the system.

作品の完成

  This week lectures were full with challenge and fun. We are going to finish our mini project - 2 single sided PCB project. A sequence of process have to follow in order to make the circuit broad function.

  First, we explore the broad that cover by circuit picture by using UV light. This process taking about 90 minutes. After that, we enter the etching room in workshop. The process conduct in this room are developing and etching. We immerse the broad in sodium solution and hot ferric acid to clean the unwanted copper on the broad. The waste product ( ferric acid ) has to handle carefully to avoid pollution. We dry the broad by cloth and cut the broad to separated equal size.

  Later, we use the sand paper to remove the green component on the broad before we drill the hole. The process later are assembling all the devices and soldering devices. The soldering process is really fun but also difficult, we need to be very be careful the avoid the interrupt and connection to another line.

  The final process is testing. We test the function of broad by using function generator which will supply the voltage to that circuit. I manage to make the LED on 2 broad function light up and I very satisfy with my work because it is too success even through the soldering is not really prefect. I pass up the broad with SMD component and wish will get a good mark...hahaha...

This is the project that I done.

This is the project with blue light LED...

Having Tour in CANON !!!

  Today lecture having a outdoor learning. We went to visit the Japanese Incorporate in Malaysia, a well known camera brand-Canon.

  Malaysia authorise Canon Incorporate located at Shah Alam, Selangor, Malaysia and named as Canon Opto (M) SDN BHD. The date of incorporation is on 14 December 1988 and the main production line is about the digital camera, EF lenses, video lens unit, and optical lenses.

  Actually, the canon company came from a small laboratory in Roppongi, Tokyo by 2 brother-in-law on November 1933. The first camera created and produced named as Kwanon, the selling price is about 400 to 500 yen, is cheap right? Is not, according to the currency at that particular time, this selling price is about 5 times of the salary of a graduated student.

  Until years 1935, Canon is named for this company and it stands for "criterion or standard of judgement " and " rule or model ", and the aim of this company is to be excellent global company.

  Canon Opto (M) SDN BHD with more than two thousands staff that including local people and foreigner. The qualification to be the member of this company is their attitude and communication skill. Few years before, the factory intake worker from Vietnam, due to the communication problem, they changed to intake Indonesian where their mother’s tongue mostly similar to Malay language. So it is really important to improve our communication skill in order to make the job smoothly and easier.

  After understanding about the history of Canon through briefing, we had a tour around the factory especially the production line. The lens production have to go through several process before use by the camera which including polishing process, centening process, and combination process. During the production, the rule and regulation is strictly for every staff to ensure the product is perfect and reduce the flaw product rejected from client.

  Went through the production line, everything is in sequence and precise even the position and line up of the machine. Every staff have own responsibility on their position and cooperated to another apartment. All staffs are busy on doing their work in a fast and precise way. Chatting to each other and using cell phone are restrict to ensure the work efficiency. Although the rules and regulation in the factory are strict but the factory also taking care on the staff's welfare by provide a lot of facilities, for example rest area.

  According to the person in charge, the factory was purchased a machine from Japan to recycle the unwanted waste which will cause the green house effect. The waste inside the factory were handle well by categorized it to that recyclable and not recyclable. This is really a good habit to make the production more eco friendly. The food waste produced also process to become fertilizer to be another purpose.

  But, I also discover something bad. When I enter the factory that mainly manufacturing lens glass, I smell something strong and pungent. Actually the machine using certain type of acid to polish the raw material glass to make the surface smooth but most the worker that responsible to this job having their work without wearing mask. After long term of period, this may cause some healthy problem and illness. So, the factory should take more concern about the worker health and safety.

  Anyway~this really a memorable trip that let me learn more about the Japan company and their working management...

Starting of Mini Project!!!

  This week lecture is the introduction about the mini project, lecturer allocated all the apparatus and material that we going to use in this mini project. The mini project we need to done is single and double sided broad. A sequence of step have to follow to make the broad function.

The sequence of making circuit broad including explosing, developing, etching, cutting, drilling, assembling, soldering, and testing.

  Before starting the project, we need to print out the circuit that have been design from ultibroad on plain white paper and transparency sheet. The circuit printed out will show the component and connection between component of both upper and bottom side. This clearly showing the composition of the devices and make the work more easier. The usage of transparency sheet is for radioactive explosing on circuit broad.

  During the process of developing and etching, we need to use the chemical component such as sodium powder and ferric acid to clean the unwanted copper on the broad. The waste product must be handle well to avoid pollution. After that we cut the board to equal separate circuit.

  The process later is drilling, we make the hole on the broad where the component located. We put the component inside the respective position and solder it. This is the process of assembling and soldering. After soldering the component, we test the circuit broad by connecting to voltage source. If the connection is precise and correct, then the LED on the broad will light up.

Multisim and Ultibroad test make me crazy!!!

After learning of multisim and ultibroad, I almost understand their function and usage in the field of engineering. We learning the way to creat, design, and analysis our circuit on multisim and transfer it to ultibroad. The ultibroad allows us to modify and visualize the real circuit on circuit plate by provide 3D view.
And it is almost the time to test our understanding on both of this software.

On tuesday, we having our test on software multisim and ultibroad, everything must be precise in order to avoid any mistake and error while making the real circuit.

Everything is going smooth on the morning of that day, our director explain the test and what he wants us to do on the particular circuit.

I success to creat 2 circuit on multisim, success to let the buzzer sound and make the LED light up. I transfer the circuit to ultibroad. Before this, I replace all the virtual component to real component and confirm the number of component as well as the wire.

When doing the ultibroad, we have to check back the circuit that we creat in multisim to make the connection bocome smoothy. This is the most difficult part because many error will occur like overlaping the wire. I tried many time to make the circuit correct, and my design was so satisfy. But, something unfortunaly happen, the computer jam and everthing is gone expecially my afford. I tried to search help from my director, but he also undefine the problem that occurred just now. I so dissappointed but i decided to redo even no much time is left.

I tried to make the circuit become simple and at least it can function well. After creat, I click the button on screen and transfer it to 3D view, but the bad thing happen again. I knew that I do not have time to redo again, so I give up. Because of this decision, I loss half of my mark in this lab test. I almost want to cry, how a unlucky day!!!

Nevermind, I need to be more hardwork on the next time, everything will be fine~haiz~

Learning Multisim and Ultibroad is Crucial as An Engineer

  This week lecture is teaching about the usage of multisim and ultibroad, two of this software are smart enough to modify the real electrical circuit that including the electronic component and the flowing of current and voltage. The lecturer showed that the different version of the software and their improvement over the year.

  Multisim is a window friendly software and is really convenient for design and analyse the circuit. It allows the user to insert different type of electronic component including basic component, input source and even some virtual sources. The user can alter and set up the value of the electronic devices, so that make the circuit function well. It allows the user to creat either series or parallel circuit, analyse and test the efficiency of the circuit by testing the voltage, current, resistance of the component.

  Multisim allow the engineers to design their own electric circuit and transform it to another software that is ultibroad. Ultibroad will show the arrangement of the devices on the real electrical panel. It also show the 3 Dimension of the panel and allows the user understands the circuit completely. But, the ultibroad restrict the using of virtual component, this make the circuit fail to transfer correctly and causing the serious error.

  As an electronic system engineer, it is really important for us to manage the usage of Multisim and ultibroad, because it will completely related to our real project later. It as the starter of creating a panel...

This is the example of multisim...

This is the example of ultibroad...

Important Device Introduction

This lecture was giving briefing about some important device including IC, organic LED and soon. The devices were using widely in all electrical applicances nowaday to perform crucial function. The devices perform specific task and they made the applicances become more sustainable and perform perfectly. All the devices work together in the electrical circuit simultanously and make the applicance more fulfill the demand of the human nowadays...

The picture showed some component in the electrical circuit, all of them are important electronic device!

Challenging Week!!!

This week really full with challenging stuff, one practical test and one oral presentation.
I was really surprise that i still remember the method to take measurement of electronic device by using multimeter and component analyser, this means I really concentrated on class...haha..
With the mistake I realised after the test, I found my weekness on this subject and I should find out some solution to solve it.
That is read more and do more!

Farhan, Uzair, and Wan explained about global positioning system.

Chin Yap, Chi Wah, and Zhi Jie explained about optical fibre.

In the oral presentation, I felt that everyone was great and I really learn more about the other electronic gadget. It is about the knowledge on the way it function and their application.
In my group's presentation, I felt very nervous but finally I did it. I knew it wasn't my best perform and wish that I will become better on the next one.

Our Minutes in Meeting...

http://www.docstoc.com/docs/100651659/MINUTES-OF-MEETING

Our Article ....Oral Presentation....

http://www.docstoc.com/docs/100558632/Touchscreens-Technology_2

I light up the LED...

Diode is a special device that having many functions.
It act as a valve that only allow 1 flow of current, as a bulb give out the light, as a filter in circuit also.
Diode consumed power and causing the voltage drop.

See how I measured the LED ( light emitting diode ) by using multimeter, as the voltage flow through the LED, it light up. It proven that I connected it with the correct way because diode is polarity.
Upon the diode has polarity, it is necessary that we defined the anode and cathode of diode.
Otherwise the device will burn out.

This week we also learn the transistor device.
When lecturer asking what is the function of transistor, no one of us can answer the question.
Actually transistor uses for control voltage, as a switch and amplifier. Transistor divides to NPN and PNP type. The lecturer explained about the usage and the method of analysing the transistor of circuit.
By using multimeter, we can easily detect the type of transistor and the pin of transistor.
As we find out the the base pin, we can easily find out the collector and emittor.
Another method is by using component analyser, this is the faster and easier method to analysed pin and voltage of transistor.

Learning Device Is Fun !!!

Tuesday lecture teaching about the different type of device, included resistor dan capacitor.
We carried out different experiment to test how the device function and learned the function of device...

Even though the general name of device are the same but it can be divided into different type.

And the cover of the devide represents the detail of the device, it showed the unit and capacity of the device.

We also learned how to take the reading of the device by multimeter.

Most of the decives we learned that day are homo type which is without terminal and some experiment is carried out to check the consequences if we wrong connect the positive and negative terminal...

This is what happen if we wrong connected the capacitor...something is horrible!!! It explore after a few second when we connect to the power supply...

Haha...just like the human...some hair is glow...hehe...so funny...

Introduction of Engineering....

Today we discussed about the future lecture schedule, it seen like a impossible mission that we have to learn such many things within 4 weeks...

But, it is really important that we totally understand and manage what lecturer teach us, it is so challenging and interest..

We decided to increase the lecture time to extra 1 more hour, that means I have to give up 1 hour sleeping time to attend the lecture. It is so difficult for me to do that but I will try because I really don't like to miss any class within the 4 years in my uni life without any reason.

This course offers a lot of practical hours and this is benefit for us so that we can manage both theoritical and practical skill. In the future lecture, we are going to do a lot of electrical practices including mini project and design...
It sound like interesting because i had get a good result when study electrical system before. Hopefully I can manage to do it...

Anywhere, fighting!!!

 It is interesting!!!

A good conduct in Electronic System...

A good conduct give us a beautiful life...
When we produce some product, we get the sourse from the environment, the raw material form earth. There are so precious and will finish soon.
Without proper conduct and design, this raw material will become rubbish one a day...
Maybe our next generation will not have a chance to enjoy the beautiful environment, even worse, they are going to live together with the rubbish.
Can you imaging the surface of earth are fully cover by waste? And our poor next generation will stay with this condition forever life.

Some manufacturer using toxic material to replace qualified material in the production line to reduce the cost and increase their profit. This is  really unscrupulous that harm the human life and our earth.
Having a good conduct in electronic system is essential that reduce electrical waste and guarantee the human life.

Regardless in the home or workplace, a good conduct ensure the hormonic in work with consider about the healthy of employers.
Learning good conduct when student life is crucial and should be a part in the education in order to protect our earth form pollution and any other human activity which is immoral to our earth.

Learning to Earn or Learning to Serve???

This lecture give me a strong impression, what a good topic that we have to think more.
Actually, what is the motive that we continue our study to the higher level?
Mr Kamal asked us a question when the lecture...
Are we going learn to earn or learning to serve? And I think for a while..
I know most of us are learning to earn, we study in university is ensure that we will going to have a better life in future. We can earn more money and enjoy our luxury life.
Firstly, I also have a thought like this. When I think more further, learning to serve is actually what i want...
I want to give my parent a better life in future so I start to learning. While we earn the knowledge the actual motive is learning to serve. Sound like we have to serve something that before we learn...
Maybe you all will get confuse about this...
So have a think now, are you learning to earn or learning to serve???

Really 1st time of me~~~haha

erm~this is the 1st time i owning my own blog and actually i don't know what i have to write...
This is a blog that records my 4 years life in university...

My lecturer asked us to update our status after the lecture, maybe it likes a homework that compulsory to do..but...it really interesting!!!...and someone may feel my blog really boring...but i really hardwork to improve it..

This course really good (haha...because no examination is required!)...and after few weeks, our coursemate and i may have a opportunity to practice in the japanese factory in Malaysia...

Today the lecturer also teached us some japanese language...REALLY INTERESTING!!!
I LIKE IT SOOOOOO MUCH!!!
I like the japanese culture soooo much since I am in Form1...
Hopefully...i will have a chance to be selected and having my study in Japan...So i have to hardwork!!!

I still waiting for the basic japanese language in the next sem!!! WoW...so excited!




After enter university, i felt that independent and self-disipline are so crucial as what my lecturer told us today...
I should change my attitude now in order to fulfill my dream in this 4 years...
Sorry that i really talk a lot of rubbish...

グッドナイト...^^